Drivers are required to periodically charge the battery of their vehicle. For this, special devices are available for sale that can satisfy the requirements of the electrical system of a car. However, most chargers are designed for a specific type of battery.
However, in everyday life, it is sometimes necessary to use devices with various types of batteries. In order not to buy a charger for each of them, there is a universal type of equipment. Such devices include Imax- B6. Charging a car battery , screwdriver, drill and other devices can be performed using it. It will be interesting to learn about the main features of the presented device to each owner of the vehicle.
general characteristics
All lead-containing batteries are serviced by an Imax- B6. Charging a car battery occurs both for one type of equipment, and for several at the same time. The device is suitable for Li-Io, Li-Fe, Ni-Cd, Li-Po, Pb, Ni-MH types of batteries.
Also, the presented device is capable of completely discharging the listed batteries. This allows the device to perform its actions in a fully automatic mode. If the item is defective, charging will cut it off.
When a certain battery capacity is reached, charging may stop. Stopping may also occur if the battery heats up to a certain temperature. For this, a special sensor (purchased separately) is connected to the device.
In addition to the listed functions, Imax-B6 can balance between 2 to 6 elements. The listed qualities make the device popular among consumers. This is really a “folk” exercise.
Appearance
In order not to purchase a fake, you need to know what it looks like when delivered Imax- B6. Charging the car battery (photo below) comes in a cardboard box. In addition to the main device, the kit includes wires for connection and instructions. The power supply in the original kit is missing.
On the device’s body there is a connector for connecting power, as well as an output for a computer. You can also connect a temperature sensor to it. On the opposite side are the balancing sockets, as well as the “+” and “-” terminals.
Above is a grille that simulates a radiator. However, these ventilation slots are located on the back of the device. Here, the original devices have a hologram of the manufacturer.
In order not to purchase a fake, these characteristic features should be paid attention to. Due to the easy repetition of the device circuit, it is produced by other plants. The quality of such devices, as a rule, leaves much to be desired.
Originality Check
It is necessary to verify authenticity by purchasing the original charger or its variants, for example, Imax-B6-AC (complete with power supply) or Imax- B6 (mini). Charging the car battery must have a hologram from the manufacturer. If it is not, it is guaranteed a fake.
If there is a sticker on the back, a special protective coating must be applied to it. It must be erased. Under the cover, the original code will be presented. Further in the instructions, you must find the address of the official website of the manufacturer.
In the appropriate form, fill in the fields with the serial number of the device and code. If the purchased device is original, an inscription about the successful operation will appear. The second time the code cannot be entered. Therefore, for a fake, when entering the appropriate data, the system will show an error.
Connectors
Imax- B6 has a certain package upon delivery . Charging a car battery almost always does not include a power supply. It can be purchased separately (inexpensively). The power supply must provide a voltage of 11 to 18 volts. A common model for 12 volts (5A) is quite suitable.
According to consumer reviews, the original kit with a power supply from the manufacturer does not work reliably enough. Overheating occurs in the system. Equipment for this reason quickly fails.
In the kit for connecting the power supply, the manufacturer supplies wires with connectors of the appropriate type. There are also other cables for connecting the charger to other devices. To enter the Imax-B6 itself, the delivery set includes wires with banana connectors. There are also wires for connecting to the T-Connectors.
Manufacturer's Instruction
There are a number of manufacturer requirements that should be followed when operating the Imax- B6. Charging the car battery, the instruction of which is included in the delivery, is carried out in accordance with certain rules. The manual is translated only into English (and with errors).
In order to properly use such a device for their own purposes, it is necessary to take into account the following requirements. Equipment in working condition should not be left unattended by the user. Also, it cannot be operated in the rain or in direct sunlight. Do not leave the device near a battery or other heat sources.
During charging, the device must be installed on a non-flammable surface that does not conduct current. If for some reason the device or the battery itself starts to get very hot, it must be immediately disconnected from the mains. A defective device is strictly prohibited.
Also, do not charge types of batteries that are not intended for this device, for example, gel, WET batteries. They have specific modes when charging.
Operational features
During the operation of the presented device there are a number of features. Its modes allow accelerated charging and storage of lithium batteries. At the usual Imax- B6 speed, the car battery (100 amperes of capacity) will charge for 20 hours at a voltage of 5A.
The user sets the mode independently. In this case, you can set limits on capacitance, time or input voltage.
If you want to restore the battery, the device is put into cyclic mode. He will perform from 1 to 5 charging and discharging procedures. Up to 5 commands can be entered into the device’s memory, which can be changed during operation.
Device control
Charging a car battery with the Imax- B6 is very easy. All necessary information is displayed. First, the device must be connected to the network. Further, the program settings are performed using 4 buttons. Their functions are spelled out in the instructions.
The Batt.Type / Stop button sets the type of battery. The microprocessor will then be able to recognize the battery.
To set the values of the selected settings, press the Inc and Dec. buttons When choosing the necessary parameters, the result must be saved. To do this, press the Start / Enter button. With its help, the charging process also begins.
Using the presented buttons, you can set the conditions for charging, discharging the batteries, as well as their balancing, storage and other modes. The user can also set the voltage and current in manual mode.
Charge the car battery
For lead-acid battery types, the Imax- B6 is intended . Charging a car battery with a nominal value of 12V is set to 14.4V. In this case, there will be no strong evolution of gases. In this case, the charging current must be set to 0.1 from the nominal capacity of the battery itself.
With these parameters, the process will be performed in the optimal mode for the battery. When discharging, it is necessary to set the current strength in accordance with the required duration of the process (10 or 20 hours). This mode can also be used to train the battery or check its capacity.
Work errors
By purchasing the presented device, the user may encounter some difficulties. There are certain errors that the Imax- B6 displays when charging a car battery. Connection break is one of the most common. The user can see such a message in any charging mode for all types of batteries.
This error code is due to the controller. It does not detect voltage from the balancing connector. If the system displays this or another error, it would be more correct to turn to a specialist for help. Especially if the device is still under warranty.
If the deadline for providing free maintenance of the device has already passed, the user can try to fix the malfunction on their own. You must have a soldering iron, as well as minimal knowledge about the device electronics. First of all, it is necessary to check operational amplifiers. Perhaps the diode through which the power is supplied from the network has failed. Breakage is most often determined in this department.
User reviews
Among the main advantages that the presented device has, the cost of Imax- B6 stands out . Charging a car battery, reviews of which are provided by experts and users, will cost about 4 thousand rubles when buying. with power supply. Fakes cost 800-900 rubles. cheaper. For such a cost, you can purchase highly specialized devices. Given the versatility of Imax-B6, this device becomes a favorite when choosing.
Among the shortcomings, users note an insufficient wire length. When charging a car battery, you have to build a complex system of cables to complete the entire procedure.
The presented device is characterized by users as reliable, durable. It performs high-quality charging and is versatile in use. Therefore, the presented charger is recognized as the sales leader in the market of special equipment for automobiles.